Page 14 of 14 FirstFirst ... 4121314
Results 131 to 135 of 135

Thread: Wet Saw Build Questions

  1. #131
    Senior Member
    Join Date
    Mar 2014
    Location
    Charleston, West Virginia USA
    Posts
    508
    Do you have room for a lid latch? Just put it on for now. Latch at 60 degrees. you can build under it.
    Bones

  2. #132
    Senior Member Zapins's Avatar
    Join Date
    Jun 2010
    Location
    CT, Hamden
    Posts
    2,061
    What about putting 4 shocks on the cabinet? Two on each side. I could put them either one right behind the other or make an arm support off the side of the box and then mount them on top of that? Then I could put them closer to the hinge and on the outside and solve the placement issue with the extra force. I could get 1200 lbs of force that way with four 300 lb shocks. I calculated it out and it should work pretty nicely if I place them between about 6 and 8" away from the hinge and have them go straight up.

    Or I could get these lambo shocks up to 850 lbs each! http://www.ebay.com/itm/2-NEW-600lbs...38.m2548.l4275

    True they won't be horizontal, but I've seen other shocks used vertically and I don't mind if that means I have to replace them a little more often.

    I looked into the torsion spring idea. It seems dangerous and difficult to find large enough springs to do what I want. Garage door openers aren't powerful enough which means I'd need to custom order which is mega bucks $$$.

    A pneumatic pump might work, but I have no idea how those come together or what specs are important to match. Would need major assistance or a list of compatible parts to get that going I think unless I am over complicating them.

    I'll definitely have a lid latch and some supports to prevent the lid opening too far or collapsing.

  3. #133
    Senior Member
    Join Date
    Mar 2014
    Location
    Charleston, West Virginia USA
    Posts
    508
    Zap,
    There is a photo in post #43, is that what you are shooting for?
    If it is, you have plenty of room for mounting the shocks on the inside.

    Did you notice the automatic off switch? LoL
    Bones

  4. #134
    Senior Member Zapins's Avatar
    Join Date
    Jun 2010
    Location
    CT, Hamden
    Posts
    2,061
    Yes the auto off switch is funny. Effective though I'm sure! I might do something similar unless I can think of a better auto off .

    This is what I want to do with the shocks. Put them on the outside but mount them the other way around so the cylinder is on top and the oil can pool at the bottom and keep the seals wet. I don't want them inside if at all possible because it will cut down on the width of the rock I can make.

    http://www.ruffntufftools.com/830202...302024-220.htm


    I found a guy who can custom make shocks to the right size and power needed so I'll make a decision on that soon and put an order in.

    Going to start work on the carriage and vice design. I think I have a pretty good idea what I need to do. Not too complicated either which is nice.

  5. #135
    Senior Member Zapins's Avatar
    Join Date
    Jun 2010
    Location
    CT, Hamden
    Posts
    2,061
    Looks like I managed to gather up enough luck and got it unloaded at home.

    Now all that remains is I need to finish designing the vice & carriage assembly. Do you all think 1/2" thick plate is too thick for the entire thing? would 1/4" work as well or better go with the heavy duty stuff?






Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •